UV Inhibitors in Polyester Gelcoats

September 1, 2002
/ Print / Reprints /
ShareMore
/ Text Size+
Table 1
Organic polymers, including polyester resins and most organic-inorganic polymers, do not suffer electrochemical corrosion, as metals do. Generally, all plastics undergo a certain degradation, either by thermal, photo, chemical or mechanical attack, or by simple outdoor weathering (temperature variations, moisture, sunlight, oxidation, biological attack, and other environmental elements).1-2

Polyester degradation is affected by solar radiation, photocatalytic admixtures, water and moisture, chemicals, oxygen, ozone, temperature, abrasion, internal and external stress, and pigment fading.3 Out of all these, the following factors, all present in outdoor weathering, are the most important to coating degradation: moisture, elevated or lowered temperatures, oxidation and UV radiation.

  • Moisture. Hydrolysis occurs when a plastic is exposed to water or humidity. This chemical reaction may be a major factor in the degradation of condensation polymers such as polyesters, where the ester group is hydrolyzed.2

  • Temperature. When a polymer is subjected to a thermal energy greater than the bond energy that holds the atoms together, it is readily cleaved.4 As a result, two macroradicals, or electron-deficient molecules, are generated.

    Most plastics are generally evaluated in three conditions of elevated-temperature exposure: elevated temperature over a long period of time, elevated temperature over a short period of time, or cyclic exposure to elevated and lowered temperatures, such as may occur during alternating day and night exposure.2

    When temperature is increased, the destructive effects are further enhanced by additional UV exposure.

  • Oxidation. Due to the presence of oxygen in the atmosphere, the most common type of radiation degradation, photooxidation, occurs on all organic polymers. Again, the process will be accelerated by UV radiation and higher temperatures. The chemical reaction can be described by the oxygen attack on the bond in a polymer chain, which may either form carbonyl groups or crosslink.

    This process is sensitized by the presence of chromophores, such as carbonyl (-C=O) containing compounds.1 By the absorption of photons (hn), the sensitizer energy is raised to an excited state; in this excited stage it may split, producing free radicals. These free radicals will then react with the surrounding oxygen molecules, forming peroxide or hydroperoxide radicals - radicals that can further attack other polymer chains, perpetuating the reaction. The oxidative degradation of polymers is catalyzed by heavy metals.4

    Different stabilizers may be used to reduce polymer degradation: antioxidants, thermostabilizers, photostabilizers, etc.

  • UV radiation. When it comes to outdoor applications, the primary concern in the material evaluation is the potential sunlight degradation when plastics are meant for outdoor use.5 Of the total radiation that reaches the earth's surface, about 5-6% of the light is in the UV region of the spectrum and usually will vary with daily environmental weather conditions.

    The photochemical effect of sunlight on a plastic material depends on the superficial absorption properties and the chemical bond energies of the material. Light wavelengths that have the most affect on plastics range from 290 to 400 nm. The wavelength of UV radiation whose photon energy corresponds to a particular bond energy in the polymer chain (see Table 1) can break the chemical bonds (through a chain scission), changing the properties, and therefore the performance of the polymer.6 The most damaging wavelength for polyesters is believed to be 325 nm.2

    Table 2
    The UV radiation degradation of plastic materials used in outdoor applications can be inhibited or delayed by introducing light stabilizing additives (also called UV inhibitors or light absorbers) into the polymer mix. Their concentration range usually is 0.05-2%.6- 7 They are part of a larger additives group, known as excited state quenchers, that either inhibit or delay degradative reactions rather than to stabilize properties, as summarized8 in Table 2.

    Theoretically, there are four different chemical methods that can be used against plastics deterioration.6 The first technique is to introduce additives that absorb light before they can contact the degradation-initiating center and the energy is dissipated as heat.

    The second way consists in deactivating the excited state of the initiating center. Again, such reactions produce energy, which is generated either in the form of heat or as fluorescent radiation.

    In the third method, the hydroxyperoxides that have been formed are transformed into other stable forms that do not generate free radicals. Metals complexes of sulfur-containing compounds are very efficient in this regard and can be effectively used at low concentrations. Dialkyldithiocarbamates, dialkyldithiophosphates and thiobisphenolates are used for this specific purpose.

    The fourth method is achieved by introducing in the system new additives (free radicals scavengers) whose purpose is to stop further reaction of the formed free radicals, by simply reacting with them and forming a stable compound. The hindered amine light stabilizers (HALS) most likely operate by this chemical mechanism. Beside HALS, nickel complexes, which are considered excited state quenchers, are also being used.

    However, the addition of UV absorbers alone may not always give adequate protection to all type of plastics; generally they are used in combination with HALS compounds.8

    The degradation process mostly affects the surface, at least in the initial stages, and results in chalking, discoloration and sometimes even loss of physical and electrical properties. The product bulk properties of impact strength, tensile strength and elongation may all deteriorate because of degradation process.

    Wypych8 also describes the sequence of events during degradation and the results of exposing coating to weather, such as chalking, discoloration or cracking. He considers gloss to be the most sensitive measure of deterioration because the degradative process affects the surface first, followed then by the color change.

    Any specific polymer may have good resistance to a particular weathering factor and may be highly susceptible to degradation when exposed to other conditions or a combination of factors.9 For example, higher temperatures will increase the oxidation rate of a plastic, as well as the rate of photochemical reactions. Exposure to lowered temperature can cause a material to become brittle; the modulus of the material will be higher, while the elongation and impact resistance may decrease. Crazing, cracking and propensity to fracture upon impact can also occur. When plastics are exposed to elevated temperature, the result may be loss of mechanical properties (mostly embrittlement, loss of impact, flexibility, and elongation) or loss of electrical properties.9 During the cyclic exposure, the alternating expansion and contraction of the plastic will eventually lead to mechanical fatigue failure and cracking. It can also result in electrical failure due to the formation of surface crazing, that may subsequently be filled by moisture and dirt, forming a conductive medium that promotes electrical tracking.

    This article evaluates the influence of several UV inhibitors on the gelcoat performance and properties. It also compares the most common types of accelerated weathering devices with natural weathering test results.

    Table 3

    Experimental

    The gelcoat is a very important part in composites and needs to perform two primary functions - protection against weather and decoration.8,10 The need for weathering studies became obvious when the gelcoat business realized that the gelcoat durability can be severely affected by the coating degradation during exposure. To predict the behavior of the plastic materials in different weather conditions prior to its field use, test methods designed to simulate natural weathering at an accelerated rate have been developed. Due to these tests, the long-term weathering performance may be predicted in a shorter time period by exposing specimens to extreme conditions to accelerate the aging process.

    While the real-time outdoor weathering exposures provide the most accurate results, they are extremely slow and accelerated testing methods were therefore needed to reduce the cycle time associated with new product development, and to have a consistent way to compare performance. Unfortunately, not all accelerated weathering tests' methods or equipment accurately predict the relative durability of the coatings because it is almost impossible to rank the degenerative power of temperature, moisture and UV radiation or their combination.7

    Table 4
    Another challenge is the variation in the natural weather conditions. Acceleration and correlation are the main two issues that must be taken into consideration when selecting an accelerated weathering method.11 Acceleration indicates how rapidly the test can be conducted using an accelerated weathering device compared with outdoor weathering. If agreement exists between the accelerated and the real-life outdoor test, then the results are valid to estimate the acceleration of the laboratory test. The term correlation is the ratio between accelerated test results and a certain real-life exposure time in outdoor conditions and practically grades the reliability of any test method or lab equipment.

    The type and degree of outdoor exposure vary greatly from place to place throughout the world, Florida and Arizona being international benchmarks for natural weathering. Florida has high intensity sunlight, annual UV and year-round temperatures, annual rainfall and humidity. Arizona features a hot, dry and high UV radiation environment, with large temperature fluctuations. With the exception of higher humidity, the Arizona exposure condition is a harsher climate. For our own real-life outdoor test, we have selected a method with a direct exposure on unbacked specimens on a wood fixture frame as per ASTM G 7-96, so that the front surface (gelcoat) of the panels faced the sun and had no cover.

    Choosing a specimen exposure angle will also have a significant effect on each of the following test parameters: solar energy dosage, specimen temperatures and moisture and time of wetness.12 The angle of exposure, called "tilt angle," has a significant impact on the specimen's response to its environment because it determines the dosage of solar radiation, rate of heat build-up and cool down, and the amount of time that the specimen is wet because of dew formation, rainfall, or drying winds. For our test, we selected a 34-deg north latitude angle, where the specimens were mounted facing south. This exposure angle is known as "Latitude angle" and provides the most solar radiation of any fixed angle.

    Table 5

    Materials

    A special modified acrylated polyester gelcoat resin and a general-purpose (i.e., conventional) unsaturated ortho polyester resin for the base core were used for this study.

    The gelcoats and the core mix were formulated using the formulations shown in Table 3 expressed in weight parts per 100 parts of neat resin (phr). These formulations and the mixing conditions do not necessarily reflect practical requirements for the resin mixes.

    For this study we selected two main types of light absorbers commonly used in the industry (a hydroxyphenylbenzotriazole and a hydroxybenzophenone), along with a HALS (piperidinyl sebacate), as shown in Table 4. The UV inhibitors were added only in the gelcoat mix in the amounts specified in Table 5.

    Procedure

    All the resin mix components were dispersed for 20 minutes in a mixer with a blade diameter of 50 mm. A shear rate of 7.8 m/sec (3,000 rpm) was applied, if not otherwise specified. With the exception of the type and amount of UV inhibitors in the gelcoats, the same single chemical composition was used for all the panels.

    A film thickness of 0.3 mm of gelcoat was drawn down on a horizontal surface and then cured in the convection type oven at 126.7 deg C for 20 minutes. A flat panel structure (1,500 gram per square meter total weight and 1.37 mm thick) was built together using the above gelcoat and the core, with 25 wt% total glass content. The whole composition was cured in the convection type oven at 126.7 deg C for 25 minutes.

    The gloss was measured on the gelcoat side of the panel at 60 deg with a Byk-Gardner micro-TRI-gloss instrument, as per ASTM D 523-85 standard. The difference ("d" Gloss) between the initial and the final (after exposure) gloss was reported.

    The color on the gelcoat side of the panel was measured with an UltraScan XE spectrophotometer from HunterLab. The CIE system of L, a, b values represents whiteness, redness, and yellowness, respectively, with the corresponding complementary colors at the opposite end of each axis of 3-D colorspace. The total color change, dE, was calculated after each exposure by the equation:

    dE = ((dL)2 +(da)2 +(db)2 )

    where: "d" represents the difference between the initial and final values on each color axis of arbitrary units.

    The following accelerated weathering tests were performed on the panels: Emmaqua, Xenon arc, and UV, along with the real-life outdoor exposure.

    The Emmaqua test is an accelerated natural outdoor weathering test performed in Arizona, where the solar radiation is magnified by a sun-tracking mirror device. A total radiant exposure energy of 280 MJ/m2, in accordance with ASTM G 90-94, Procedure B, is considered to be the equivalent of one year of real-life natural outdoor exposure in Arizona. The specimens are mounted unbacked in an aluminum frame, with the gelcoat surface toward the sun.

    Xenon arc test exposure was performed as per ASE J 1960/ASTM G 26 standards, with an Atlas Ci65-A instrument.

    UV exposure was performed with a Q-U-V Accelerated Weathering Tester instrument from The Q-Panel Co., with a combination of condensation and fluorescent UV, as per ASTM G 53. UV-B lamps were used on the gelcoat side of the panels with the following continuous cycle: 4 hours of UV at 50 deg C, followed by 4 hours of condensation at 40 deg C.

    Table 6

    Results and Discussion

    In the first study, as shown in Table 6, we evaluated the real-life weathering data (color change and gloss change), after one year of natural outdoor exposure. As can be seen, there is not much difference between the hydroxyphenylbenzotriazole and the hydroxybenzophenone; regardless of their amount, their performance is very much alike. Not the same thing can be said about the HALS: by itself, it does not offer any color change (yellowing) protection to the polyester gelcoat. The yellowing protection does increase with the amount of UV absorber(s), but the efficiency is not linear. The best results were obtained, however, with the larger amounts of additives and with the synergistic effect of both inhibitor(s)/HALS.

    While the yellowing differences are considered important, one year of outdoor exposure is not long enough to evaluate the gloss retention. At this level, the differences reported between the systems are too small to be considered indicative to actual performance differences. It should therefore be considered as a fact that the color change does actually occur prior to chalking and loss of gloss.

    Figure 1
    With system #6 (0.2 phr UV-5411), we have also evaluated for comparison a longer real-life outdoor exposure (up to four years), along with several accelerated weathering tests, as presented in Figures 1-4.

    Figure 1 shows that the color change continued to rise up to three years, followed by a plateau, and even a decrease in the total color change. The gloss continued to decrease during the years. The color change "stability" seems to occur when the gloss has lost about 30 units.

    Figure 2
    In the Emmaqua test (Figure 2), both the color change and the gloss retention are similar to the real-life exposure patterns: the color change reaches a peak around the third year of exposure, then decreases, while the gloss continues to decrease in time. It should be noted that the Emmaqua exposure is more "abusive" on both respects (yellowing and gloss loss), probably due to the more extreme conditions of the Arizona desert, along with a frequent moisture treatment of the gelcoat.

    Figure 3
    In the QUV exposure (Figure 3), the color change continued to occur up to about 250 hours of exposure, while the gloss remained practically unchanged. This is another proof that the yellowing occurs prior to chalking. The equivalent to one year of real-life exposure may be 24-48 hours for yellowing and about 200 hours for the gloss change, a very large discrepancy. With the QUV exposure, a very dramatic color change is occurring, however with no correlation to a factual real-life outdoor exposure, possibly due to the high concentration of UVB radiation. The color change plateau is reached when the gloss has lost about 20 units. Compared to Emmaqua, and related to the color change, the chalking (and subsequently, the gloss loss) is very much delayed. This means that the continuous moisture layer due to the condensation process in the QUV is not as "efficient" as the hourly water spray shocking of the gelcoat surface in the Emmaqua test.

    Figure 4
    In the Xenon arc exposure shown in Figure 4, the weathering data have followed the same pattern: the color change occurred first and continued to increase up to about 500 hours (about 20 days), with some gloss changes only after 400 hours of continuous exposure. After this peak, the color change reached a plateau and then decreased, while the gloss loss continued to increase. The equivalent to one year of real-life exposure may be considered about 300 hours for yellowing and about 450 hours for the gloss retention. The total color change is very much in line with the real-life outdoor weathering, and somehow with Emmaqua, but again the gloss loss is very much delayed. As opposed to the QUV, the yellowing in the Xenon arc instrument occurs not only due to the UV radiation, but probably even more so due to the heat exposure.

    The data reported suggests that up to a gloss loss of about 30 units, the rate of yellowing is much greater than chalking; after that, the chalking prevails and the apparent yellowing is stopped and even reversed. Premature or very delayed chalking will drastically change the aesthetics of the gelcoat. The degree of curing of the resin, its chemistry, hardness and the thickness of the gelcoat become therefore very critical.

    Conclusion

    From a range of UV inhibitors, two UV light stabilizers and a HALS were evaluated in the polyester gelcoat of the FRP panels. Both the hydroxyphenylbenzotriazole and the hydroxybenzophenone evaluated in this study provided equal results. The total color change was significantly reduced when combined with the HALS. By itself, the HALS does not provide any surface stability improvement in the gelcoat. The best results were obtained with the highest amounts of inhibitors.

    To evaluate the gloss retention, more than one year of outdoor weathering is necessary. Due to the complex multi-process (photolysis, photooxidation, hydrolysis) nature of degradation chemistry, no theoretically based model exists to predict deterioration associated with weathering. There are however several proposed lab methods, which were tested in our evaluation. Each one can provide important information, but none actually can accurately match the real-life outdoor weathering data. In our proposed weathering model, we believe that the color change occurs first, followed by a gloss reduction due to chalking.

    The evaluation of an UV inhibitor (or mixtures of inhibitors) against another UV inhibitor (or mixtures) becomes also even more challenging because of the specific spectral emission wavelength of each instrument, which, unfortunately, are different one from another and more importantly, than the solar radiation.

    For more information on UV inhibitors, contact Lasco Composites, 8015 Dixon Dr., Florence, KY 41042; phone 859/371.7720; fax 859/371.1913; e-mail cezarcapanescu@fuse.net.

    References

    1. Seymour, R.B. Long-Term Environmental Factors, Eng. Plastics, Vol. II, (1988)423-432.

    2. Delre, L.C.; Miller, R.W. Engineering Plastics, Vol. II, (1988)575-580.

    3. Ashbee, K. Fiber Reinforced Composites, Lancaster, (1993)317.

    4. Seymour, R.B. Chemical Susceptibily, Eng. Plastics, Vol.II, (1988)571-574.

    5. Nichols, J.W. Chemistry of Polymers, Cambridge, (1991)135.

    6. Miller, E. Engineering Plastics, Vol. II, (1988)493-507.

    7. Plastic Design Library, Effect of UV Light and Weather, NY, (1994),IV,V.

    8. Wypych, G. Handbook of Material Weathering, Toronto, (1995)357-518.

    9. Maccani, R.R. Engineering Plastics, Vol. II, (1988)68.

    10. Nistor, C.; Ripszky, S.; Izrael, Gh. Materale Termorigide Armate, Bucuresti, (1980)108.

    11. Crump, L.S. Durability of Gelcoats, CI 51st Conf., (Feb.1996)3.

    12. Supplier, Q-LAB Tech. Bulletin LL-9025, (1998).

  • Did you enjoy this article? Click here to subscribe to PCI Magazine.

    You must login or register in order to post a comment.

    Multimedia

    Videos

    Image Galleries

    Coatings Trends & Technologies 2012

    This event took place September 11-12, 2012 at the DoubleTree Hotel Chicago in Oak Brook, IL. CTT is a 1 1/2-day, comprehensive program that covers the most current coatings technology in short, informative technical sessions, and provides a resource-rich exhibition area for formulators, chemists and raw materials suppliers to make meaningful connections and conduct business.

    Podcasts

    THE MAGAZINE

    PCI Magazine

    PCI cover April 2014

    2014 April

    The April issue is hot off the press for the American Coatings show. A few of our topics this month include smart coatings, TiO2 and a new biocidal active.

    Table Of Contents Subscribe

    AC Show

    Will you be attending the AC Show? If “Yes”, stop by PCI’s booth #242 to say hello.
    View Results Poll Archive

    THE PCI STORE

    PCI-Cover0613-120px.jpg
    PCI Additives Reference Guide

    Encyclopedia of information on the properties and uses of coatings additives.

    More Products

    Clear Seas Research

    Clear Seas ResearchWith access to over one million professionals and more than 60 industry-specific publications,Clear Seas Research offers relevant insights from those who know your industry best. Let us customize a market research solution that exceeds your marketing goals.

    Virtual Brochures

    PageCollageClick on the Virtual Brochures page to view multiple categories that list downloadable product literature from leading industry suppliers.

    STAY CONNECTED

    FacebookTwitterYouTubeLinkedIn